- Induction Brazing two positions on a stainless steel manifold Type:
Class: HF Induction BrazingIntro: Objective Simultaneously braze two positions on a stainless steel manifoldMaterial Stainless steel manifold 4” (101.6mm) long, 1” (25.4mm) in diameter and nico brazeTemperature 1800 F (982 C)Frequency 198 kHzEquipment • UM-UHF-20kW induction heating sys…
- Induction Brazing Brass Trap Block Type:
Class: HF Induction Brass SolderIntro: Objective Block is heated to 1400F to braze trap tube to assemblyMaterial brass block and pre-formed tubesbraze pre-formsTemperature 1400 F (760C)Frequency 357 kHzEquipment UM-UHF-20kW induction heating system including• Coil: custom-designed 2-turn split
- Induction Brazing Plumbing Type:
Class: HF Induction BrazingIntro: Objective A copper-brass fluids union is brazed under constrained conditions (onboard a submarine), where access is limited and flame is not allowed.Material copper and brass plumbing componentsTemperature 750C (1380 F)Frequency 245 kHzEquipment UM-UHF-20
- Induction Brazing carbide Type:
Class: HF Induction BrazingIntro: Objective Braze a carbide wear pad to steel for automated surgical forcepsMaterial Steel assembly 1/2” (127 mm) long, 1/8 “ (3.175 mm)cross section Carbide wear pad Braze alloyTemperature 1350-1400 F (732- 760 C)Frequency 313 kHzEquipment UM-UHF-4 kW, i…
- Induction Brazing Steel-carbide tool Type:
Class: HF Induction BrazingIntro: Objective Provide a solution to this steel-carbide brazing applicationMaterial • Body 10mm; carbide tip 57 x 35 x 3 mm• Braze shim• Braze flux whiteTemperature 750C (1382F)Frequency 152 kHzEquipment UM-UHF-10kW induction heating system, equipped with a …
- Induction Brazing Steel to Steel Type:
Class: HF Induction BrazingIntro: Objective To braze O-ring Face (ORFS) sleeve or male connector to a steel tube.Material • Steel tube, 1 inch (2.54 cm) OD• O-ring Face Seal sleeve and a male connector fittings• Preform braze rings• White SureFlow flux• Steel support mandrelTemperatur…
- Induction Brazing carbide to steel Type:
Class: HF Induction BrazingIntro: Objective Braze a carbide sleeve to a steel ‘T’ shankMaterial 2.0” (51mm) OD carbide sleeve, 1.0” (25.5mm) high braze joint, 1.5 ” (38 mm) steel ‘T’ , 50% silver braze ringTemperature 1292 F (700 C)Frequency 257 kHzEquipment • UM-UHF-10 kW inductio…
- Induction brazing copper to copper Type:
Class: HF Induction Brass SolderIntro: Objective To braze copper to copper bus bar assemblies togetherMaterial • 2 copper bus bars 6” (152.4mm) wide, 2’ (609.6mm)long, 2 copper bars 6”(152.4mm) wide, 18” (457.2)long & 3/8” (9.65mm) thick• braze shim preforms and white fluxTemperature…
- Induction Brazing stainless steel Type:
Class: HF Induction BrazingIntro: Objective1st Application: Braze hub assembly to needle holder2nd Application: Braze Large tube to ring joint Material 1st Application: Steel hub assembly and needle 0.1” dia (2.5mm)2nd Application: Steel tube 1” OD (25.4 mm) and ringTemperature 1400 F (7…
- Induction Brazing copper tube & pipe Type:
Class: HF Induction BrazingIntro: Objective Braze brass fitting with o-ring to various diameters of copper tube.Material Various copper tubes ranging from 3/8” to 7/8” diameter and 2-3’ long, female brass fittings with o-ring, silver solder rings and glass beaker.Temperature 1300 F (704…
Recommended
induction brazing SS steel by handheld induction coil
induction melting silicon and steel
magnesium oxide acidic furnace for induction melting glass
induction preheating gas pipeline by full air cooled clamp induction coil and DSP induction heater
induction melting with Titanium alloy pot by customized induction coil
induction melting aluminium for casting wire wheel
induction heating steel knife
induction deicing for aircraft carrier,naval vessels, naval craft, naval ships and boats, warship