- Induction Hardening steel screw threads or steel nails Type:
Class: Induction HardeningIntro: Objective Heat steel roofing screw to 1650 F to harden the threadsMaterial Steel roofing screws of varying diameters less than 1.25” (31.75mm) diameter, 5” (127mm) longTemperature 1650 F (899 C)Frequency 291 kHzEquipment • UM-UHF-6 kW induction heating …
- Cap Sealing With Induction Heating Type:
Class: Other Induction ApplicationsIntro: Objective An induction heater is used to heat a polymer laminated aluminum foil in 0.5 to 2.0 seconds. The heat produced in the aluminum foil melts the polymer that bonds to the neck of a plastic container.Material Aluminum foil, polyethylene, polypropyle
- Induction Sealing Shampoo Container Type:
Class: Other Induction ApplicationsIntro: Objective To heat an aluminum foil inside a plastic shampoo cap for sealingMaterial 2.0” diameter, plastic flip top cap, with a 0.9” diameter aluminum foil sealTemperature 250 – 300 F (120 – 150 C)Frequency 225 kHz Equipment 10 kW, induction heati…
- Induction Cap Seal Container Type:
Class: Other Induction ApplicationsIntro: Objective To heat an aluminum in-cap laminate to a temperature of 350F in order to seal the laminate to the containerMaterial 3.5” (100mm)Temperature 350 F (177C)Frequency 300 kHzEquipment UM-UHF-4.5kW induction heating system; custom-designed work coil;
- Induction Sealing aluminum foil to plastic bottle Type:
Class: Other Induction ApplicationsIntro: Objective To seal a 1.5” (38.1mm) diameter cap with foil to a plastic bottle.Material 1.5” (38.1mm) diameter cap with 1.5” (38.1mm) diameter aluminum seal, plastic bottleTemperature 250-300 F (121-149 C)Frequency 309 kHz Equipment •UM-UHF-6kW induction …
- Induction Brazing carbide to steel shaft Type:
Class: HF Induction BrazingIntro: Objective Brazing a cone shaped carbide to a stainless steel shaft for a diggerMaterial Cone shaped carbide 1.12” (28.4mm) dia, 1.5”(38.1mm) tall, stainless steel shaft 1.12” (28.4mm) dia and various length, black brazing flux and braze shimsTemperature…
- Induction Curing epoxy Type:
Class: Other Induction ApplicationsIntro: Objective Heat the end of an aluminum copier roller to 400 F (200 C) to cure epoxyMaterial Aluminum roller 4.75” (120mm) diameter, 2’ (0.6m) long with 1.5” (38.1mm) thick plug at endTemperature 400 F (200 C)Frequency 52 kHzEquipment • UM-HF-25 kW induc…
- Induction curing coating Type:
Class: Other Induction ApplicationsIntro: Objective Curing a coating on both sides of an aluminum piston at a rate of 1” (25.4mm) per secondMaterial 4 aluminum pistons weighing 1lb (.45kg) each, 3.75” (95.25mm) dia and 2.5” (63.5mm) highTemperature 225 F (107.2 C)Frequency 6 kHzEquipment • UM-…
- Induction Curing adhesive Type:
Class: Other Induction ApplicationsIntro: Objective To Cure adhesive in aluminum filter endsMaterial Aluminum filter, steel end caps & plastisol adhesiveTemperature 200 FFrequency 277 kHzEquipment UM-UHF-6kW induction heating system, equipped with a remote workhead containing two 0.1uF capac
- Induction Curing Ceramic Fiber Type:
Class: Induction Tempering or PreheatingIntro: Objective To heat-cure a NextelTM Ceramic fiberMaterial Ceramic fiber 30,000 (9,145) ft(m) Steel tubeTemperature indicating paintTemperature 1300(700) F(C)Frequency 70 kHzEquipment UM-HF-45kW, 50-450 kHz solid-state induction power supply with a remote he
Recommended
induction brazing SS steel by handheld induction coil
induction melting silicon and steel
magnesium oxide acidic furnace for induction melting glass
induction preheating gas pipeline by full air cooled clamp induction coil and DSP induction heater
induction melting with Titanium alloy pot by customized induction coil
induction melting aluminium for casting wire wheel
induction heating steel knife
induction deicing for aircraft carrier,naval vessels, naval craft, naval ships and boats, warship