- Induction Bonding Gasket to Nut Type:
Class: Induction BondingIntro: Objective To heat a steel sombrero nut prior to gasket bondingMaterial • Steel sombrero-shaped nut approx. 2” (50.8mm) diameter, 2” (50.8mm) in height • gasketTemperature 350 F (176 C)Frequency 266 kHzEquipment • UM-UHF-6kW induction heating system, e…
- Induction Brazing thin walled tube Type:
Class: HF Induction BrazingIntro: Objective Braze a NI-SPAN-C alloy tube to a steel cap in a hydrogen atmosphereMaterial NI-SPAN-C alloy tube (5mm) dia, steel cap (7mm) dia, (7mm) long, nickel braze, quartz tube and hydrogenTemperature 1875 F (1024 C)Frequency 313 kHzEquipment • UM-UHF-20
- Induction Brazing piston valve Type:
Class: HF Induction BrazingIntro: Objective Brazing a steel piston valve assemblyMaterial Steel piston valve 4.5” dia (11.43cm), tungsten carbide plate and brazeTemperature 1350 FFrequency 91 kHzEquipment • UM-HF-90kW induction heating system, equipped with a remote workhead containing s…
- Induction Brazing brass faucet Type:
Class: HF Induction Brass SolderIntro: Objective Brazing two joints on a brass bathroom faucet assemblyMaterial Brass bathroom fittings 1” OD, brazing rings, fluxTemperature 1148 F (620 C)Frequency 90 kHzEquipment • UM-HF-90kW induction heating system, equipped with a remote workhead containi…
- Induction Brazing manufacture needles Type:
Class: HF Induction BrazingIntro: Objective Brazing stainless steel housings to stainless steel tube for gas assembly used in the manufacturing of needlesMaterial 2 stainless steel housings .25” (6.35mm) dia, .675 (17.1mm) & .54” (13.7mm) in length, stainless steel tube .031” (.78mm…
- Induction Brazing copper pivot Type:
Class: HF Induction Brass SolderIntro: Objective Brazing a copper pivot assemblyMaterial Two copper uprights 2” (5cm) wide x 4” (10.2cm) high, copper base 3” (7.6cm) x 2” (5cm) and .5” (1.3mm) thick with 2 channels for the uprights to the slide into, braze shims and black fluxTemperature 1…
- Induction Brazing heat-sensing probe Type:
Class: HF Induction BrazingIntro: Objective To heat a coil and a wire assembly to 1300F (704C) within 60 seconds for brazing.Material Platinum coil, steel wire, braze pasteTemperature 1300F (704C)Frequency 307kHzEquipment UM-UHF-6KW output, remote heat station containing one 1.2 microfara
- Induction Brazing dental tools Type:
Class: HF Induction BrazingIntro: Objective To heat a steel tip and shank assembly to 1300F (704C) within 3 seconds for brazing with induction heating instead of torch brazing.Material 0.1” (2.54mm) diameter steel tip & shank, 0.07” (1.78mm) diameter braze ringTemperature 1300F (704C…
- Induction Brazing steel orthodontic parts Type:
Class: HF Induction BrazingIntro: Objective To heat a batch of orthodontic parts to 1300F (704C) within 1 second in an inert atmosphere for brazing.Material Small stainless steel orthodontic parts, silver braze alloy, no flux, 3 1/ 8” (79.3mm) graphite susceptor disk with 1” (25.4) cente…
- Induction Bonding Rubber to Steel Type:
Class: Other Induction ApplicationsIntro: Objective To bond rubber gaskets to the top and bottom of a steel gas tank assembly.Material Flat and round rubber gaskets, steel gas tank assemblyTemperature 300 to 350F(148.9-176.7C)Frequency 183 kHz for the flat gasket; 231 kHz for the round gasketEqui
Recommended
induction brazing SS steel by handheld induction coil
induction melting silicon and steel
magnesium oxide acidic furnace for induction melting glass
induction preheating gas pipeline by full air cooled clamp induction coil and DSP induction heater
induction melting with Titanium alloy pot by customized induction coil
induction melting aluminium for casting wire wheel
induction heating steel knife
induction deicing for aircraft carrier,naval vessels, naval craft, naval ships and boats, warship