- Research the heating effects Type:
Class: Other Induction ApplicationsIntro: Research the heating effects Objective Heating stainless steel disc & tantalum disc to 1400F (760C)Material Stainless steel and tantalum discs approx 1/2” (12.7mm) diameter. End product is radioactivity counting plateTemperature 1400 F (760C)Freq…
- Induction Preheating oil drilling shaft Type:
Class: Induction Tempering or PreheatingIntro: Preheating oil drilling shaft Objective To preheat a steel pipe to 500F (260C) before welding.Material Steel shaft assembly 5” to 8” OD (127-203.2mm) with a 2” (50.8mm) heat zone.Temperature 500F (260C), if higher temperatures are required, heat ti…
- Induction Sintering copper powder Type:
Class: HF Induction BrazingIntro: Sintering copper powder Objective Sintering copper powder to a stainless steel shaftMaterial Steel shaft & shell assembly, approx 2” (50.8mm) diameter, 2” (50.8mm) tall, copper powderTemperature 1600 F (871 C)Frequency 54 kHzEquipment • Power o…
- Induction Heating motor Type:
Class: Other Induction ApplicationsIntro: Heating motor Objective Heat steel to help bond an injection molded piece and help the reflow.Material Steel motor body, 60 x 60 x 27 (2.4 x 2.4 x 1.1) mm(in)Temperature 260C (500F)Frequency 237 kHzEquipment • Power of 20kW induction heating system, …
- Induction Heat braided cable Type:
Class: Other Induction ApplicationsIntro: Heat braided cable Objective Prior to cutting, heat a short section of a hardened steel cable coated with a polyethylene sheathing.Material Multi-strand braided stainless steel cable 0.5 in. (1.27 cm) OD enclosed within a polyethylene sheathingTempera…
- Induction Hermetically sealing glass Type:
Class: HF Induction BrazingIntro: Hermetically sealing glass Objective Provide a hermetic seal of glass enclosed resistor to a leadMaterial ResistorKovar rings, 0.1 inch (0.254cm) diameterGlass tube slightly larger than 0.1 inch (0.254cm) diameter, 0.5 (1.27) inch lengthMetal leadTemp…
- Induction Tempering Spring Type:
Class: Induction Tempering or PreheatingIntro: Tempering Spring Objective Temper a spring by heating it to 300C (570F) in 2 – 4 secondsMaterial Stainless steel AISI 302 springs- different length from 60 to110 mm outer diameters 8 mm.- wire diameter from 0.3 to 0.6 mmTemperature 300C (570F)Freque…
- Induction Heat the end of catalytic converter Type:
Class: Other Induction ApplicationsIntro: Heat the end of catalytic converter Objective Heat the end of lorry catalytic converter exhaust system. The assembly must be held at target temperature for 200 hours, whilst the assembly is vibrated to test the weld strength.Material SteelTemperature …
- Induction Heat the plough discs Type:
Class: Other Induction ApplicationsIntro: Heat the plough discs Objective To heat the circumference of plough discs before hot rolling (sharpening) processMaterial Flat Boron steel discs, OD 460 to 710 mm (18 to 28”) thickness 3.2 to 10 mm (8/64 to 25/64”)Temperature 725C 1335FFrequency 75 …
- Induction Heating steel rivets Type:
Class: Induction JointingIntro: Heating steel rivets Objective Heating steel rivets prior to head formingMaterial steelTemperature 1292 F (700C)Frequency 83 kHzEquipment • Power of 7 kW induction heating system, equipped with a remote workhead containing one 1.5μF capacitor.• An …
Recommended
induction brazing SS steel by handheld induction coil
induction melting silicon and steel
magnesium oxide acidic furnace for induction melting glass
induction preheating gas pipeline by full air cooled clamp induction coil and DSP induction heater
induction melting with Titanium alloy pot by customized induction coil
induction melting aluminium for casting wire wheel
induction heating steel knife
induction deicing for aircraft carrier,naval vessels, naval craft, naval ships and boats, warship