- Induction Heating brass mandrel die Type:
Class: HF Induction Brass SolderIntro: Heating brass mandrel die Objective Water-cooled brass mandrel die, nylon LDPE catheter, “K” type thermocouple and temperature controller.Material materials, supplies involved in the applicationTemperature 400F (204C)Frequency 325kHzEquipment Power …
- Induction Heating steel mandrel tip Type:
Class: Induction Thermal TreatmentIntro: Heating steel mandrel tip Objective Heat a water-cooled steel mandrel to 700F (371C) to form a high quality Teflon catheter tip.Material Teflon catheter tubing, mandrel assemblyTemperature 600-700F (315-371C)Frequency 376 kHzEquipment • Power of 10kW…
- Induction Heating Catheter Tipping Die Type:
Class: Induction Thermal TreatmentIntro: Heating Catheter Tipping Die Objective: To heat an aluminum catheter tipping die to above 2850F within 2 to 5 seconds for the forming of catheter material. Presently, heating is performed in 15 seconds with older induction equipment. The customer woul…
- Induction Heating fan blades for welding Type:
Class: Induction WeldingIntro: Heating fan blades for welding Objective To uniformly heat jet engine turbine fan blades to 1800F (982.2C) within five minutes for a welding applicationMaterial Jet engine turbine fan blades with 2”(50.8mm) length tipTemperature 1800F (982.2C)Frequen…
- Induction Soldering Co-axial Wire Type:
Class: Induction SolderingIntro: Soldering Co-axial Wire Objective To solder center-conductor and shielding braid of wireassemblies to 500 (250) F(C).Material • Customer-supplied assemblies• Temperature indicating paint• Flux-cored solder wireTemperature 500 (250) F (C)Frequency 2…
- Induction Soldering wires onto connector Type:
Class: Induction SolderingIntro: Soldering wires onto connector Objective Heat connector assemblies for solderingMaterial Device assemblyTin plated brass terminals Solder pasteTemperature 500F (260C) 5-7 secondsFrequency 360 kHzEquipment Power of 6 kW induction heating system equippe…
- Induction Soldering satellite antennas Type:
Class: Induction SolderingIntro: Soldering satellite antennas Objective Soldering steel onto GPS body for phone antennaMaterial Thin copper foil 0.3mm (0.01 in) thick Ceramic body 12mm (0.47 in.) long x 7mm (0.28 in.) wideTemperature 200 C (392 F)Frequency 371 kHzProcess Time 5 secon…
- Induction Soldering brass Type:
Class: HF Induction Brass SolderIntro: Soldering brass Objective To solder a brass end cap to a series of copper tubesMaterial Preassembled heat exchanger with copper tubes and 2 brass end caps 2.36” (60mm) OD, 0.08” to 0.12” (2 to 3mm) thick at both ends, liquid solderTemperature 302F …
- Induction Soldering circuit boards Type:
Class: Induction SolderingIntro: Soldering circuit boards Objective To heat post, lead or lead-free solder preforms for various circuit board soldering applications.Material Upper and lower circuit boards, small and large lead or lead free preforms.Temperature < 700 F (371C) depen…
- Induction Soldering brass and copper Type:
Class: HF Induction Brass SolderIntro: Soldering brass and copper Objective To heat brass and copper for soldering application on medical equipmentMaterial Brass ring, brass and copper pieces 5.11” (130mm) long, 4.3” (110mm) OD & 0.3” (7mm) at thickest point and solder ringsTemperat…
Recommended
induction brazing SS steel by handheld induction coil
induction melting silicon and steel
magnesium oxide acidic furnace for induction melting glass
induction preheating gas pipeline by full air cooled clamp induction coil and DSP induction heater
induction melting with Titanium alloy pot by customized induction coil
induction melting aluminium for casting wire wheel
induction heating steel knife
induction deicing for aircraft carrier,naval vessels, naval craft, naval ships and boats, warship